Catalogue
Systems
Adia Systems is a compact engineering supplier for desktop CNC, light milling, and the kind of small-cell work that needs calm specification.
- 01
Microaes Desktop
Microaes Desktop suits bench-top CNC work where sheet parts, jigs and one-off prototypes need controlled travel in a small footprint. It is typically specced with attention to cutter size, spindle duty and power stability, especially in South African workshops where dust, heat and shared plugs can affect repeatability.
- 02
Light Milling Kit
Light Milling Kit is aimed at small-part machining where aluminium, plastics and thin non-ferrous stock need firmer workholding than router-style setups allow. Users usually check rigidity, chip clearing and pass depth settings first, because light milling behaves very differently once feed, tool stick-out and lubrication are off.
- 03
Proto Bench
Proto Bench brings the machine, support surface and surrounding workflow into one bench-scale setup for regular sample work. Space for tooling, stock, clamping and swarf handling matters here, particularly in compact Gauteng and coastal workshops where every square metre gets used twice.
- 04
Edu Desktop
Edu Desktop is arranged for teaching basic CNC habits without moving straight into heavy industrial complexity. Attention normally goes to safe startup checks, tool changes, simple CAM routines and the kind of operator mistakes that show up during first cuts in school, college and training lab use.
- 05
Acrylic Cell
Acrylic Cell adds enclosure control for chips, visibility and operator separation where desktop routing runs near people or clean work areas. Clear panel condition, access points, extraction routing and noise behaviour all matter once plastics start building static and fine swarf around the machine.
- 06
Aluminium Light
Aluminium Light covers lighter aluminium cutting where setup discipline makes more difference than brute force. Feed rate, tool geometry, hold-down pressure and chip evacuation need to be matched properly, otherwise edge finish, chatter and recutting show up long before material limits are reached.
- 07
Fixture Set
Fixture Set supports repeat placement for small batches, test pieces and parts that need the same zero point each time. Datum choice, clamp reach and clearance around the cutter are the usual checks, especially when jobs switch between plastics, composite sheet and softer metals.
- 08
Spindle Soft
Spindle Soft deals with the running side of the spindle rather than only peak speed on paper. Ramp settings, bearing behaviour, noise changes and heat over longer sessions are worth watching, particularly where fine dust, long duty cycles or unstable supply can shorten service life.
- 09
Cam Starter
Cam Starter is for getting parts from drawing to toolpath without loading a small workshop with unnecessary complexity. The useful checks are post output, origin logic, cutter library basics and sensible step-down values, so first jobs do not waste stock through simple setup errors.
- 10
Dust Shoe Kit
Dust Shoe Kit helps capture swarf at source when MDF, acrylic and similar materials make a mess of guides, rails and surrounding benches. Brush height, hose routing and shoe clearance need to suit the cutter length, otherwise extraction drops off just when chips start packing around the cut.
- 11
Vise Compact
Vise Compact is intended for smaller machined parts where edge access and quick resetting matter more than large-table capacity. Jaw alignment, part lift, parallels and clamp pressure should be checked before cutting, because light components can shift under the tool long before the grip looks suspect.
- 12
Training Pack
Training Pack focuses on the first operating habits that prevent damaged cutters, lost zero points and confused job setups. It usually covers material loading, spindle warm-up, safe tool changes, basic feeds and speeds, and the routine checks that make more sense after the first few runs.
- 13
Coastal Pack
Coastal Pack deals with rust risk, storage, and maintenance details that usually show up after the first easy jobs.
- 14
Highveld Pack
Highveld Pack deals with dust, dry air, and workshop wear that become obvious once regular cutting starts.
- 15
Night Shift
Night Shift covers unattended setup, safe restart checks, and the issues that show up once after-hours runs are under way.
- 16
Export Week
Export Week deals with crating, paperwork, and handover details that matter once the machine leaves the workshop.
- 17
Training Day
Training Day deals with setup habits, operator basics, and common mistakes that surface after the first session.
- 18
Spares Bridge
Spares Bridge keeps cutters, collets and wear parts sorted once the first jobs move from test cuts to daily use.